Top 10 usual forklift crashes ， forklift procedure must focus on these issues ！.

Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the person in front can not be located, causing a moving crash.
Situation 2: In order to preserve the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which practically causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift driver does not put on the safety belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a seat belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will certainly affect the security of the forklift. .
3. After dumping, the fork should be reduced to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will cause the automobile to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be raised other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the thing impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever run with diseases or hide them.

filling and discharging.
1. When fork-loading items, the range between both forks must be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift must be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork suggestion need to not touch other Stand-on Electric Pallet Stacker products or objects. The tons needs to be stabilized with very little back tilt of the gantry to make sure that the load does not move backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy positioning of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be slow and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they run into large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll things.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, Stand-on Electric Pallet Stacker railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844